Sterling Water Heater Sediment Removal

Posted by on Mar 30, 2015 in Gas Water Heater Repair Sterling VA, Water Heater Repair Sterling VA | 0 comments

If you have a trouble with sediment, you’re most likely currently knowledgeable about it. Gas fired water heaters in certain commonly show that there is a sediment trouble with rumbling sounds each time the tank cycles, while still keeping excellent water temperature level. Thankfully, sediment can quickly be eliminated, and help prevent the need for a Sterling water heater repair.Water Heater Repair Sterling

If you have a gas water heater, turn the control to pilot. If you have an electric design, you need to switch off the power at the panel. Next shut down the water above the heater so no brand-new water can get in the tank. Then affix a hose to the drain valve. The various other end of the hose need to ideally go to a floor drain, although a pail can likewise be made use of.

Open the drain valve to get rid of all the water from the tank. The majority of the sediment needs to be gotten rid of by this basic act. Keep the drain valve open, however switch on the water too, permitting some to get in the tank. Turn off the water after a couple of minutes. Repeat this numerous times to coax as much sediment out with the water.

As a last procedure, close the drain and fill the tank a minimum of half full. Then you can drain it for a last time to get rid of any last remains of sediment. To avoid more usual sediment troubles, you can set up a sediment filter for your tank if your trouble is primarily with sand. A sand filter need to be set up on the cold trunk line.

Occasionally sediment can likewise congest the drain valve itself. Preferably you need to have the ability to wash the valve out under high pressure, however occasionally the valve should be changed after a cleaning. You can achieve this job while the tank is still complete, simply switch off the gas or power and await the water in the tank to cool. You need to likewise not make use of any water in your residence will finishing the replacement.

To get rid of the drain valve, merely make use of a huge groove joint pair of pliers to turn off the old valve. Then set up a replacement valve by turning it in clockwise. Make certain to make use of pipe thread sealing tape or pipe joint substance on the threads to make sure that the connection will prove out.

If you are preparing to get rid of the drain valve, you could think about prior to setting up the replacement valve offering your tank a last flush. This is finest done if you have a floor drain that will rapidly drain the water and sediment.

The follow video illustrates this process:

Many individuals incorrectly think that a sediment filled tank or a dripping drain valve is source to change the whole hot water heater. By these basic upkeep actions, the majority of residents need to have the ability to take care of any troubles on their own. Naturally, Water Heater Repair Sterling VA is here to assist with this or any other water maintenance that should be accomplished for you.

Have a look at a few of our additional related water heater repair and maintenance articles:

Eliminating Water Heater Odors

The Reasons of a Water Heater Tank Explosion

Eliminating Water Heater Odors

Posted by on Mar 11, 2015 in Water Heater Repair Sterling VA | 0 comments

Are you experiencing an issue with foul-smelling odors originating from the water originating from your water heater? It happens from time to time for a few various reasons. Here is what Water Heater Repair Sterling VA suggests to do for getting your water smelling and tasting much better fast.

Reasons for Sterling Water Heater Smells?

According to Soquel Creek Water District, “The smell is the result of four factors that must all be present for the odor to develop. These factors include:

  • A high concentration of sulfate in the raw water
  • Sulfate reducing bacteria, non-toxic to humans (sulfate is reduced to a sulfide state by the bacteria)
  • Little or no dissolved oxygen in the water
  • Hydrogen (a component of water which may be present due to water conditions reacting with the anode)”  Read more:

The most typical source of hot water smell is germs getting into the water supply. This is more widespread in houses that utilize well water and cities that utilize wells as their water supply.

With a water heater temperature level setting of 140 degrees or more will assist in reducing the development of germs within the water storage tank.

Exactly How to Eliminate Stinky Water Odors

The following instructions discuss the best way to use chlorine bleach to wash a water heater.

The electric or gas leading to the water heater tank has to first be turned off.

Next, the cold water supply off that goes to the tank needs to be turned off.

Open the hot water faucet of the kitchen area sink to enable air to get in the tank.

With a a yard hose connected to the storage tank drain valve, drain the water inside the water heater.

Then shut the drain valve after it is empty.

The next step is putting in the bleach.
If the hose for the cold water going in the storage tank is a flexible line, unscrew it from the tank. Otherwise, one will likely need to take off the pressure relief valve, which is more involved. For electric water heaters, one of the elements can be removed.

Utilize a funnel to put bleach within the tank.
Use 5 ounces of bleach for each gallon of the tank capability.
Case in point – A 50 gallon water heater will require 250 ounces of bleach, that is around 2 gallons.

Re attached the water line or pressure relief valve.

Fill the tank back up with water once again.

Shut the hot water faucet of the kitchen area faucet as quickly as all the air runs out the line.

Operate all the hot water appliances till the odor of bleach is noticeable. We want to eliminate the germs that are located in the water lines likewise, not only within the water heater.

Let the water to remain in the tank and water lines undisturbed for 2 to 3 hours.

Empty the storage tank once again and refill it. This time let it set undisturbed for thirty minutes and drain it one more time.

Fill the tank back up. Open all the hot water appliances and let them run till the odor of bleach is gone.

For gas water heaters, relight the water heater pilot burner. For electric water heaters, turn the electricity on once again.

Additionally, by replacing the anode rods, or perhaps the type employed can work as the next video shows:

More Resources

Controlling Odors in Hot Water Heaters – City of Fellsmere

Solving rotten-egg odor in water heaters

Your Household Water Quality: Odors in Your Water

Repairing a Noisy Sterling Water Heater

Posted by on Feb 26, 2015 in Water Heater Repair Sterling VA | 0 comments

Water Heater Repair Sterling VA is frequently being consulted to check out at water heater. Popping and knocking noises can be caused by problems with the water heater, but it’s likewise an aggravation. We are going to explore the most typical reason your water heater may possibly begin creating noise and what you can possibly do to calm it down! Prior to consulting a Sterling professional, have a look at one of the most typical water heater issues and remedies.

The most likely reason a water heater creates noise

Again, if the sound is an indicator of an issue with the heater that issue is more than likely sediment build up. The sediment originates from the water in the storage tank. It is primarily composed of calcium and magnesium debris and is primarily an issue in residences which may have hard water.

If the sediment starts to accumulate at the bottom of the storage tank, it traps a little part of hot water below it. This triggers the hot water to boil as the tank operates. The sounds noticed are the bubbles popping through the sediment.

Furthermore, the sediment itself could be the reason for the sounds. The sediment sits at the bottom of the tank and can get burnt up creating unusual sounds. And sometimes, the sediment will get carried up to the top of the tank and breaks off creating sounds as it plunges back down, bumping the sides on its way.

How to avoid a water heater from creating noise

If sediment build-up is what’s creating the sounds, the heater should be examined. Hot Water Heater Repair Sterling VA can accomplish this and provide the tank a flush or advise a different remedy.

You can also stop sediment build-up by having expert routine maintenance carried out on the storage tank approximately annually. This technique involves flushing the tank of any sediment.

An additional excellent solution is to add a water softener in your Sterling residence. Water softeners eliminate minerals from the water prior to it entering the water heater, dramatically minimizing sediment build up.

To learn more about other probable problems and remedies provide Water Heater Repair Sterling VA a phone call!

Sterling Plumbing Repair

Posted by on Feb 17, 2015 in Drain Cleaning Sterling VA, Plumbing Repair Sterling VA | 0 comments

Carrying out plumbing upkeep is one method to conserve on your water costs. As a fact, it can assist you prevent significant residence problems which can be rather expensive in the long term. From routine drain cleaning to changing the water heater, there are various methods to make sure that your plumbing system is in great working condition. In case the issue is past your skills, you can always give Water Heater Repair Sterling VA a call.

Appropriate Plumbing Care and Maintenance

To be able to save water, you need to make sure that the plumbing system is constantly in great working condition. Overruning commodes and leaking pipes can really cost countless dollars. Likewise, you require to inspect for concealed leaks to ensure that you are not squandering cash on the water costs. Attempt to take an appearance at the water meter and observe if there are uncommon modifications that might be an obvious indicator of unidentified leakages.

Sterling Plumbing Repairs

Carrying out small repairs is likewise extremely essential in making sure that the plumbing system is operating effectively. In case of troubles, ensure you do not postpone the repair work for this could cost a great deal of cash particularly when the circumstance gets even worse. Even with leaks, definitely be timely. To be able to not squander water, ensure to resolve right away any water damages found. In addition to plumbing repairs you could likewise desire to safeguard your pipeline throughout cold weather condition. According to professionals, insulated pipes are less likely to come apart. This will in some way avoid from handling expensive leaking repair works.

Various Other Sterling Plumbing Maintenance Tips

One method to assist in protecting against water damages due to leakages is to inspect pipes throughout the early spring and winter season. If possible, contact us to examine the plumbing system for any possible outflow. Always keep in mind that regular upkeep is one method to save water. Routine safety evaluation does not just assist in conserving water, but it can likewise be a help in decreasing the regular monthly expenses.

If you think plumbing upkeep is a bit complicated, you are completely mistaken. Prior to you even employ somebody who might look after the repair work for you, you ought to understand that easy plumbing jobs can be carried out without expert assistance. Cleaning drains is one of the upkeep jobs property owners can quickly carry out by on their own. So start the practice of staying mindful of the condition of your plumbing system at home – it will pay off in the long term!

Advantages of Employing Heat Pump Water Heaters at your Home

Posted by on Feb 4, 2015 in Heat Pump Water Heaters, Water Heater Repair Sterling VA | 0 comments

Today Water Heater Repair Sterling VA wishes to go over utilizing a heat pump as another option to an electric water heater. Common thought has long been that heat pump water heaters aren’t really energy efficient at heating water, however new research is challenging this concept.Water Heater Repair Sterling VA

As stated by Sarah Widder, of the Department of Energy’s Pacific Northwest National Laboratory, “Heat pump water heaters can use up to 63 percent less energy than traditional electric water heaters. When water heating makes up about 18 percent of U.S. residential energy use, heat pump water heaters offer a real opportunity for energy savings.” (read more…)

The analysis concludes that the method that heat pump water heaters are attached to the air ducting can help lessen overall energy consumption of the house, displaying that these kinds of heat pumps might not have as much influence on the entire cooling and heating of the house, as has long been believed.

The research, that was done in the summer and winter of 2013, organized a pair of equivalent real world test scenarios. The primary variation was with one heat pump not making use of ducting, and the other making use of 2 different ducting options. The summary ended up being that the test case with the thoroughly ducted heat pump water heater would decrease yearly power usage by 4.2 %.

The investigators also agreed that even more examining needs to be made to try other choices also and to better analyze the home cooling aspects of a heat pump.

Heat pumps are designed to get high efficiency and be less expensive to operate as compared to always heating water in a storage tank water heater. At this time, heat pump water heaters are approximately 1 % of new water heater product sales in the U. S.. They are more expensive than conventional water heaters to install but through the running expenses will be able to off set that in the long term. This is what the Department of Energy has to say.

Where the heat pump is situated in the property has quite a lot regarding the level of efficiency one will receive from it, based on

If you have any queries on this technology and want to find out if it could possibly be a fine match for your Sterling house, contact us! We are always here to give ideas on our water heater repairs and installations!

The Reasons of a Water Heater Tank Explosion

Posted by on Jan 22, 2015 in Gas Water Heater Repair Sterling VA, Water Heater Repair Sterling VA, Water Heater Safety | 0 comments

In terms of needing to undertake upkeep on ones water heater, it is a rather minimal maintenance device.  Even so, one significant component of it must be examined routinely.  Water Heater Repair Sterling VA wishes to pass on this safety material concerning ones water heater today.Water Heater Repair Sterling

Too much temperature if merged with tank deterioration inside of the storage tank can lead to an explosion. Any time the water temperature is under 212 degrees Fahrenheit, one shall be protected from an explosion, though there is a risk of scalding at that temperature.  However, if the water temperature is over 212 degrees, water changes into steam, which will enlarge to 1,700 times the space it takes up as water. This is the time an explosion can happen.

Cautionary Signals of a Water Heater Explosion

The leading sign is if one goes to get hot water from a faucet and only steam comes out.  Without delay shut off electric power if one possesses an electric water heater.  If one possesses a gas hot water heater, shut off the gas valve on the water heater.  Next, give us a call to come evaluate the scenario.

Minimizing Potential Water Heater Dangers

The most essential routine maintenance endeavor having a water heater is to examine the pressure relief valve, also known as the T&P valve, on a usual schedule.   This valve helps control the pressure accumulation on the interior of the water storage tank to avert a threatening increase in temperature and overpressure.

Be careful, the water release with a T&P valve is often rather hot. If you do not feel safe evaluating the valve contact us.  In addition, executing any kind of fixes to the valve should really be executed by a expert plumbing repair provider.

How to Test the T&P Valve

Clear the space near the overflow pipe and floor drain.
Lift up the test handle for about 5 seconds or until the water runs clean.
Let go of the handle.
If the T&P valve keeps on running with water, raise the handle up and down rapidly to have it reseat itself.  One may need to do this a handful of times.  IF it has not been tested for a while, it might be difficult to raise it at first.  Avoid using an excessive amount of force, although could need to make use of just a little.
If the T&P valve continues to have water coming out, it should really be changed.

Additional points to watch out for are rust on the stem of the valve.  If there is any water seeping out of the valve stem or out of the drain valve.

Interested in far more strategies?  Look at Water Heater Repair Sterling VA’s additional articles right here:

Changes to Water Heater Regulations

Maximize Water Heater Efficiency

From around the Web:

The Aquanta smart water-heater controller promises to slash your energy bill

Home maintenance checklist: Fall

Changes to Water Heater Regulations

Posted by on Dec 19, 2014 in Water Heater Repair Sterling VA, Water Heater Replacement Sterling VA | 0 comments

There are adjustments that will be occurring in April 2015 from the federal government on water heater laws.  The new requirements deal with the efficiency of all newly produced water heaters.

What Will New Water Heater Standards Mean to Sterling Homeowners?Hot Water Heater Repair Sterling VA

Well the higher efficiency specifications will be a good factor naturally.  Even so, it will undoubtedly increase the expense of new water heaters.  The price increase will be due to the additional cost of manufacturing the water heaters with more insulation in them.  A side effect of doing so, will increase the measurements of the water heaters.  So if a property owner is changing the present one, the new gas water heater storage tank will likely consume more room, which may be an dilemma if the current area the storage tank is in is a restricted fit.

One other modification is for 55 gallon water heaters or larger will need to change to a PVC flue, for metal pipes aren’t going to be permitted any more. This will lead to an extra cost it the flue pipes have to be replaced when putting in a new water heater.

Water Heater Repair Sterling VA is not recommending that one is required to go out before April 2015 and purchase a new water heater, but if ones present water heater is more than ten years of age, it is getting near to the end of its life cycle. One can simply wait, however in so doing, the newly produced water heater will need to satisfy the new, more expensive requirements.  One is able to purchase currently available water heaters ahead of the deadline day, and may opt to do this.

Reported by …. an “older-model 40-gallon tank is estimated to cost homeowners $277 a year to operate. The new models are estimated to cost $263.”

Here’s what the Department of Energy has to state:
“Standards mandatory in 2015 will save approximately 3.3 quads of energy and result in approximately $63 billion in energy bill savings for products shipped from 2015-2044. The standard will avoid about 172.5 million metric tons of carbon dioxide emissions, equivalent to the annual greenhouse gas emissions of about 33.8 million automobiles.”

The following video by Rheem describes the new codes effectively:

Do not think twice to get in touch with us with any inquiries on a new water heater installation or replacement.  Hot Water Heater Repair Sterling VA is always here for you!

Leaking Sterling Water Heater Pressure Relief Valve

Posted by on Dec 9, 2014 in Gas Water Heater Repair Sterling VA, Water Heater Repair Sterling VA | 0 comments

The pressure relief valve of a water heater has a vital job – ensuring the water heater tank does not explode. So with that in mind, Water Heater Repair Sterling VA wishes to ensure property owners know ways to best look after it. They will certainly leak when the valve wears out or when the water storage tank pressure gets greater then the relief point.Hot Water Heater Repair Sterling VA

We suggest that a minimum of twice a year, homeowners test to see to it the pressure relief valve, or T&P valve as we will call it, is working correctly. All one needs to do is raise the deal with for a few seconds and let go of it. It must snap back to its original position. When it is lifted, one may hear the noise of pressure being released , just like the noise of air coming out of a tire pump when being disconnected. Also, a little water might come out too. Both are regular. If the valve has not been tested in a long time, it may stick at first as well.

Nevertheless, if the handle doesn’t snap back, or if it continues to leak a little water, that is not regular. If it still leakages some, raise the handle a couple of more times to see if it does re-seat itself. You could wish to wait a day or so it see if it re-seats itself before presuming it needs to be changed.

Water Heater Repair Sterling would choose to manage any T&P valve replacements for you, so though water heaters are usually relatively maintenance free, there are some safety precautions one must be mindful of. With that in mind here is an overview of a pressure relief valve replacement.

1. The gas to the water heater has to be switched off, or the breaker for an electric water heater.
2. The cold water cut-off valve has to be closed next.
3. The valve below the T&P valve has to be opened to drain a little water in order to relieve some of the pressure in the storage tank.
4. The overflow pipe of the T&P valve has to be removed. It may need to be cut off if it is soldered or securely glued.
5. The pressure relief valve needs to be unscrewed with a pipe wrench.
6. Wrap the brand-new T&P valve with Teflon tape and screw it in place. See to it the overflow pipe opening is positioned away from the storage tank.
7. Reattach the drain pipe, likewise making use of brand-new Teflon tape.
8. Turn the water back on, and examine your work for any leakages.

The following video gives an introduction of this procedure:

Water Heater Winterizing

Posted by on Dec 1, 2014 in Water Heater Repair Sterling VA, Water Heating Savings | 0 comments

We love to share ideas on how to save on energy expenses at home here at Water Heater Repair Sterling VA. Here are some of the best ways to get ones water heater ready for the winter.

An easy way to inspect ones water heater’s need for insulation is to put ones hand near or on the outside of the storage tank. It is feels really warm, insulating the tank is suggested. During the winter this heat loss you just felt can accumulate. Conversely in the summertime, if the water heater is located inside the home, and not in a garage, it can add heat to the room that you are trying to cool. The heat you feel is undoubtedly heat being lost. If it is not warm at all that is a great indication that the tank’s internal insulation is in pretty good shape. Brand-new water heating units are being produced with a great quantity of internal insulation today. You can inspect the manufacture’s label to see exactly what the R-value is. If it R-24 or greater, one ought to be in terrific shape without having to include an insulation blanket to the water heater.

Sterling Water Heater Blankets

The remedy for this heat loss is with a water heater blanket or wrap. Initially check with your energy company, for some have insulation kits at minimized costs for property owners. A hot water heater blanket will can be found in various sizes depending upon the gallon size of the storage tank. The higher the R-value, the more insulation power it has. We would recommend getting at least an R-11.

The blankets are easy to install. They will have insulation tape to complete the joints of the blanket. The shinny or vinyl side goes on the exterior.

For gas water heaters, wrap it all around, leaving the top flue unwrapped, and unwrapped around the controller on the bottom. Also, do not wrap the T&P valve lever, or the bottom of tank for that is where air gets in. For electric water heaters, the top can be wrapped for there is not an exhaust flue, however do not wrap the heating-element access panels.

Water heater blankets will last quite a very long time. You may even have the ability to use the very same one again whenever the water heater is replaced, providing it’s the very same size storage tank.

Water Heater Pipe Insulation

There are two kinds of pipe insulation that should be utilized for a water heater. For pipes that are within 6 inches of the water heater exhaust flue, fiberglass insulation wrap ought to be made use of and ought to be attached with either high temperature aluminum tape or wire. Foam insulation sleeves can be used for all the pipes that are further away then 6 inches of the flue then.

The U.S. Department of Energy suggests that house owners insulate a minimum of 6 feet of the pipe coming into and from the hot water heater. This can increase the temperature level at the faucets 2 to 4 degrees and conserve cash on heating. We likewise suggest wrapping both the hot and cold pipes too just since every little bit helps.

Energy Savings from Sterling Water Heater Insulation

Insulating an ineffective hot water heater can cut the cost of running that heater by 5 % to 10 %. Depending upon the design, that can conserve anywhere from $5 to $20 per year, which means a water heater blanket can be paid for in 1 to 4 years. Adding insulation might minimize standby heat losses by 25 % – 45 % and conserve about 4 % – 9 % in water heating expenses.
What others round the web are saying:

Sterling Water Heater Installation Costs

Posted by on Dec 1, 2014 in Water Heater Replacement Sterling VA | 0 comments

The typical life expectancy of a traditional tank-style natural gas water heater or electric water heater is around 8 to twelve years, so the prospect of needing to replace a water heater is a typical house improvement. Water Heater Repair Sterling VA has discussed some of the elements that influence the setup expenses here.

The costs to install a brand-new Sterling hot water heater do range in rate depending on the company performing the installation, and depending upon the kind of water heater installed. As an example, energy-efficient tankless water heaters do cost more to set up, though those expenses can be recouped over the life of the device. Take a look at this tool from that will offer a price quote on water heater installation costs for the part of the nation one stays in.

Water Heater Installation Cost Factors

Without seeing the area that ones water heater will be installed or replaced, it is hard to give a specific idea of the expense. If it is a water heater replacement, and is being replaced with a similar sized and design of heater, the setup costs will be extremely reasonable. If one is changing to a different kind of water heater, like from an electric to a gas or tankless device, the setup costs will be greater due to the fact that we will need to possibly install gas lines and hookups.

Another factor to consider is to see to it a replacement water heater will be up to code with what is required now, not with what the code was ten to 12 years ago when the current water heater was installed. Also, there is the potential that the current water heater was not up to code when it was initially set up either! Which can be the case if a previous property owner did the installation him or herself.

Because of the safety aspects involved with water heaters, it is definitely best to have a professional plumbing business manage the installation. One, many house owners will not have a good idea of exactly what the code requirements are. One threat element is that electric water heaters utilize 240 volts of electrical power, which is extremely unsafe to work with if not experienced in doing so. Water Heater Repair Sterling spends a lot of time dealing with poorly set up water heaters.

Another safety concern with not having a professional set up ones water heater is working with natural gas lines. This, too, can be unsafe, and a scenario where there can not be any leakages.

A last safety concern is with appropriately venting the exhaust to make sure carbon monoxide gas leaves the home. Carbon monoxide poisoning happens more often than the majority of people think, and it is best to ensure one has a carbon monoxide detector in ones house too. According to the Centers for Disease Control, unintentional carbon monoxide poisoning triggers 400 deaths each year and 20,000 visits to the emergency room.

Other factors to consider with installing is making sure it is plumbed correctly, there is enough clearance and ensuring drip pans are geared up, if required.

How to Thaw Frozen Sterling Water Pipes

Posted by on Jul 10, 2014 in Plumbing Repair Sterling VA, Water Heater Repair Sterling VA | 0 comments

Cold weather can trigger much damage to ones water pipes in your home we know at Plumbing Repair Sterling VA. This past winter season particularly was a rough one for many people with having frozen water pipes. Frozen pipes can crack or rupture due to the fact that as water freezes, it expands. With enough growth, pipes will certainly establish cracks. The cracks may not be visible however they will certainly leak nonetheless when the ice melts. If a frozen area of pipeline is caught in time, there may be no damage; but it must be thawed prior to any more freezing takes place. Shielding pipes from freezing is the best plan, however if you are reading this, then that will certainly have to take a backseat to defrosting the frozen pipes. To discover how to avoid pipes freezing in the first place.Water Heater Repair Sterling VA

Caution: Please read our safety info prior to trying any testing, upkeep or repairs oneself. Some devices could rely on a cold water supply and suffer damage without it.

If there is a sluggish trickle at the faucet, leave the faucet open. The streaming water will certainly help to prevent a full frozen blockage. In addition, the streaming water may assist to melt the existing partial obstruction. Continue with the following steps to make sure the pipes thaw entirely.
Find the Frozen Piping

The initial step to thaw frozen pipes is to locate the area of pipe and shut off the regional water supply to it. To identify whether an area of pipeline is frozen, just feel it. Frozen pipeline will feel very cold, while pipeline with complimentary flowing water will certainly feel especially warmer. Look for a pipeline through which water is still flowing to utilize as a contrast. After a couple minutes of running, the pipeline ought to be around 50 degrees or so. If you have an infrared thermometer, it makes finding frozen pipes easy.

If there is no water at any of the taps in your home, the major water line may be frozen someplace between the meter and where the water line enters your house. Usually this line is buried, and buried at the in your area mandated depth to shield it from freezing. There is little to be done to thaw a buried water line. The only course of action is to rebury the line deeper, below the frost line, to make sure versus future freezes.

In severe freezes, there may be numerous frozen areas of piping in different susceptible locations. The very first indicate examine is where the water line comes out of the ground and where it enters your home. Any exposed pipeline is susceptible if it is exposed to outdoors air, even if it is in your attic, unconditioned basement or crawlspace.

Exterior walls, even when insulated, may get cold enough to freeze pipes inside the wall. Pipes that pass near an exterior vent in your home go through chillier air and are a good location to start hunting. If there is no water in only one part of your house, then the frozen pipe is probably in an exterior wall, attic, crawl space or basement.

As soon as you find the frozen area, if the pipe is accessible, examine it aesthetically and by running your fingers over the pipe to feel for cracks or splits. If you find damage, you may wish to get repair materials all set prior to thawing the piping. If the piping is not available, continue reading for strategies to take care of tough to reach pipes

Before you start the defrosting procedure, open water taps on the frozen line to permit water, steam or pressure to escape. This will certainly permit water to drain out as the ice melts and will certainly inform you if you have been successful in melting the obstruction.

How you heat the pipes depends upon the kind of pipe and the area. But in all cases begin closest the tap and work outward. Never ever heat a pipe with direct flame or boiling water. Heating a pipe too rapidly can lead to bursting, damage and injury.

How to Thaw Plastic Pipes

Available pipes can be warmed with a hair dryer. Keep the dryer moving and do not concentrate it on any one place too long.

Hot damp rags can be utilized to heat up pipes. Just immerse a rag in hot water (about 110 degrees F) and cover it around the pipe. Replace the rag when it cools.

A grounded, water resistant heating pad can be wrapped around the pipe and readied to the lowest heat setting.

How to Thaw Metal Pipes

While a flame can be utilized to heat accessible copper or steel pipes, it is not suggested to use a direct flame on any pipeline as this increases the danger of damage to the pipeline as well as presenting a fire threat. Never heat up the pipe any warmer than you can easily put up with holding the pipe bare handed and always utilize a flame spreader to diffuse the flame. Never ever utilize a flame on plastic pipe.

Do not hesitate to speak to Plumbing Repair Sterling VA with concerns on handling frozen pipes or for assistance in an emergency situation.

Maximize Water Heater Efficiency

Posted by on Jun 13, 2014 in Water Heater Repair Sterling VA | 0 comments

Few of our customers at Water Heater Repair Sterling VA do not want to be as energy reliable as possible with all of their house costs, including their water heating costs. So, we chose to put together a list of things that will certainly help house owners do simply that.Water Heater Repair Sterling VA estimates that 14-25 percent of a house’s energy use is from heating water, and it also makes up part of the electric costs too. The following tips will help optimize ones water heater’s efficiency.

  • Relying on the amount and frequency of the need for hot water, a tankless water heater could be an excellent investment come time to have a water heater replacement. They are more costly than standard storage tank water heaters, but over the lifetime of the system can be more cost effective. Not to mention the possible energy cost savings of running the tankless water heater.
  • If the temperature level of the heater is set above 120 degrees, reducing it can save some energy use too.
  • If one is lucky enough to be building a brand-new house or doing a remodel, attempt to position the water heater as close the location of the house that will utilize the most hot water. Water heat lost while flowing through the pipes will certainly be lessened.
  • A solar water heater might be a great investment too, and not as dependent on the area of the country one lives in as most people would believe. Heck, one can even make one with the amount of details online, though as plumbing professionals ourselves, we would like to assist.
  • Insulate, insulate and insulate even more. All exposed pipes, not only the hot water ones, need to be wrapped with insulation. One can think about making use of a water heater jacket or blanket in the cold weather season to help keeping the heat inside the storage tank. New tank water heaters are made well with a good insulation value, however every bit will assist.
  • This might be hard to do (at least I understand it would be in my house with several females) but take much shorter showers.
  • When changing a water heater, make certain it is the proper size for the amount of water that will be used usually. Many times we have seen that house owners have too big of a water heater, which raises the quantity of energy needed to heat the water … and water that will certainly not be utilized.

Sterling water heaters are fairly repair free but a yearly evaluation and some minor upkeep will help lengthen its life expectancy and conserve cash with it performing at maximum performance. Give us a call to schedule an annual check.

Sterling Water Heater Carbon Monoxide Poising Prevention

Posted by on Jun 5, 2014 in Water Heater Repair Sterling VA, Water Heater Safety | 0 comments

We have actually recently seen a number of news reports about carbon monoxide gas poising being connected back to a water heater as the source and so felt it essential to share some about that potential today. Yes, any fossil fuel burning device creates this fatal gas. Consisting of water heaters. Nevertheless, with the appropriate installation of the water heater, in addition to periodic maintenance, and a working carbon monoxide detector in the house, one can sleep securely.Water Heater Repair Sterling VA

Causes of Carbon Monoxide Poisoning

Carbon monoxide gas (CO) is a colorless, odor free gas that is a bi-product of the burning of a nonrenewable fuel source like wood, gasoline, coal, natural gas, or kerosene. Breathing in carbon monoxide fumes not only prevents oxygen from being utilized appropriately by the body, however likewise causes damage to the central nervous system. Persons with existing wellness troubles such as heart and lung illness are specifically susceptible, as are infants, kids, pregnant women, and the elderly.

Sources of Carbon Monoxide

The winter heating period is when a majority of carbon monoxide gas direct exposures happen due to using unvented supplemental heaters. An unvented supplemental heater is a kind of space heater that utilizes indoor air for heating and vents the gases produced in the heating process out into the home. The majority of heaters of this kind use kerosene or natural gas for fuel. While more recent designs have oxygen sensing units that shut off the heater when the oxygen level in the area falls below a particular level, older designs do not have such safety features. Because of these safety problems, unvented space heaters have been prohibited in several states. Other sources of carbon monoxide gas are malfunctioning cooking devices, tobacco smoke, obstructed chimneys, auto exhaust, malfunctioning furnaces and gas clothes dryers, wood burning fireplaces, and a water heater.

Symptoms of Carbon Monoxide Gas Poisoning

Here are the most usual symptoms of carbon monoxide poisoning but they are not constantly the same for each individual who has actually been exposed and often times resemble having food poisoning or the flu. A physician can assist in identifying for sure.

queasiness and vomiting
rapid heart beat
cardiac arrest
loss of hearing
fuzzy vision
loss of consciousness or coma
respiratory failure

Protection By Correct Gas Appliance Venting

The CDC provides the following details on preventing CO2 poisoning by ensuring ones appliances are vented correctly.

  • All gas appliances must be vented so that CO will not build up in your home, cabin, or camper.
  • Never burn anything in a stove or fireplace that isn’t vented.
  • Have your chimney checked or cleaned every year. Chimneys can be blocked by debris. This can cause CO to build up inside your home or cabin.
  • Never patch a vent pipe with tape, gum, or something else. This kind of patch can make CO build up in your home, cabin, or camper.
  • Horizontal vent pipes to fuel appliances should not be perfectly level. Indoor vent pipes should go up slightly as they go toward outdoors. This helps prevent CO or other gases from leaking if the joints or pipes aren’t fitted tightly.  (read more…)

It is definitely essential to have CO2 detectors in the house. The Colorado State University Extension provides the following tips when selecting a CO2 alarm.

  • Some inexpensive alarms consist of a card with a spot (spot detectors) that changes color in the presence of CO. The absence of an audible signal does not meet UL or IAS requirements for alarms, so these devices do not provide adequate warning of CO.
  • Some CO alarms have a sensor that must be replaced every year or so. The expense of this part should be a factor in purchase decisions.
  • Battery-operated alarms are portable and will function during a power failure, which is when emergency heating might be used. Batteries must be replaced, although some alarms have long-life batteries that will last up to five years.
  • Line-powered alarms (110 volt) require electrical outlets but do not need batteries. They will not function during a power failure. Some line-powered alarms have battery backups.
  • Some alarms have digital readouts indicating CO levels. Alarms with memories can help document and correct CO problems.  (read more…)

The following video provides some nice safety ideas for water heaters.

Not to scare anybody, but we also wanted to include the following video of a water heater install that is not working correctly and is harmful.

Please see a medical professional immediately if you think that you or a member of your household could have carbon monoxide poisoning. Water Heater Repair Sterling VA can not stress enough the requirement of ensuring a professional plumbing repair business services and installs any water heater equipment in your house or business.

Replacing a Heating Element in a Sterling Water Heater

Posted by on May 20, 2014 in Water Heater Repair Sterling VA | 0 comments

If your water is not heating up appropriately and you believe a faulty heating element follow these 7 steps on testing and replacing it. Bad elements are common troubles specifically in older water heaters that are been in a few years. This can happen to a more recent heater also. This is quickly identified and changed it may need a little perseverance.

Water Heater Repair Sterling VA

Note: It is best to have a trained plumbing professional perform these steps. Water Heater Repair Sterling VA just wanted to share the process for doing with our readers.

Tools required: Ohm/Volt meter, heating element socket, [both of which can be bought at a hardware shop], screw vehicle drivers Phillips and flat head.

Step one: Heating elements that go bad are easily detected by very first switching off the power to the heater then removing the access covers one at a time and inspecting each element separately. This will likewise work on loud elements, ones that have calcium accumulation. The access covers are normally on the side of the tank one ahead one on the bottom. Turn supply of water off and drain the tank unless one is experienced at changing elements with a full tank.

Step 2: After getting rid of the leading access cover, get rid of the insulation that lags it this ought to have been cut at the manufacturing facility. The insulation will come right out. Then raise the plastic cover to expose the element. This will be on the bottom half of the cover.

Step 3: Remove one wire off the element then put the meter on ohms and touch both contacts to see if it reads. If it does not read the element is most likely bad and requires replaceing. If it reads then continue to examine the next one. In electric water heaters there is a bottom and a top element.

Step 4: After determining where the bad element is eliminate both wires making sure the power is off. Put the element socket on a cog and turn the element counter clockwise removing it. Some force might need to be put into this.

Step 4: Put the Gasket on the new element and hand tighten where the old element was and turn clockwise up until tight. Complete tightening the element with the ratchet.

Step 5: Put the wires back on seeing to it they are snug.

Step 6: Fill the tank with water opening the hot water valves in our home to draw out air from the lines. Eliminate aerators on any faucets that are open and put them back on when completed. After the water is flowing in the sink or tub turn it off. Inspect for leaks after this is done.

Caution: Do not turn electricity on prior to the tank is full or another element could be destroyed.

Step Seven: Turn the electricity back on put the insulation and covers back on. The hot water issue will be repaired.

Don’t hesitate to contact Water Heater Repair Sterling with any questions you may have.


How to Repair an Electric Water Heater

Electric Water Heater Element Tests

How to Test a Water Heater Element Video


Enhanced by Zemanta

What is the Perfect Sterling Water Heater Temperature

Posted by on May 15, 2014 in Water Heater Repair Sterling VA | 0 comments

There are diverse views on what is the very best temperature at which to set ones water heater. Water Heater Repair Sterling VA will be sharing a few of the various views with specific evidence from those sources in order for one to make his/her own choice on the subject.

First of all, the default setting most water heater makers have their tanks set at is 140 degrees. If you have never inspected this already on your Sterling Water Heater, that could be the temperature it is set. Likewise, it can be tough to understand for sure exactly what the temperature setting is due to the fact that numerous times the temperature dial does not have actual degrees written on it, simply warm, hot, really hot … something to that effect. Some people feel they are pre-set at a higher temperature level so it feels remarkable to have a great deal of hot water – sort of like trying to create good brand name awareness in consumers.

In regards to energy savings, by turning a water heater down from 140 to 120 degrees, it will conserve between 6 to 10 percent of total energy used. That equates to in between $6 to $20 a year in a lot of cases.

Let’s begin with the most likely the most popular source, the U.S. Department of Energy. They suggest a setting of 120 degrees. The link to their website above provides lots of good info on the best ways to reduce ones hot water consumption and expenses. It is for sure worth a read.

Now for the health threats of too low of a temperature level setting. It can be concluded that Legionella bacteria has the ideal development range in between 68 to 122 degrees. It is believed that 25 percent of all water heaters have varying levels of Legionella bacteria contamination.

Legionella bacteria causes a type of pneumonia and is passed to people when one breathes in water contaminated with the bacteria – generally in showers, whirlpool baths and even air conditioning systems. Drinking the water is generally ok. It is a concern with having the bacteria get in ones lungs.

The Centers for Disease Control and Prevention estimates 8,000 to 18,000 Americans contract the illness each year. 5 to 30 percent of the cases are fatal.

According to OSHA, “At low levels of contamination, the chance of getting Legionnaires’ disease from a water source is very slight. The problem arises when high concentrations of the organism grow in water systems. Water heaters, cooling towers, and warm, stagnant water can provide ideal conditions for the growth of the organism.”  (read more)

Cases to not have the water heater temperature level set at 140 degrees would be if there are kids in the house or possibly with elderly individuals too. The risk of being burnt if the faucet was fully on hot water can be too great. Undoubtedly, any individual living in the home that is at threat of contracting Legionella Disease should have it set at 140.

In Conclusion

So choose if there are any issues of individuals burning themselves if the water temperature level is too high. Also, be conscious of anyone who has concerns of contracting Legionella Disease. Given that the yearly cost savings of turning the temperature level down is just about $20 many the time with the average home’s hot water use, it may be a good option to keep the temperature level above 120 degrees simply for the health related advantages; nevertheless, Hot Water Heater Repair in Sterling VA will let you make the call.

Water Heater Repair Sterling VA

Explore more visuals like this one on the web’s largest information design community – Visually.

Enhanced by Zemanta

Sterling Water Heater Safety

Posted by on May 9, 2014 in Water Heater Repair Sterling VA | 0 comments

Water heaters are pretty basic on the face of it, and they’ve changed not very much in the past 50 years suggests Water Heater Repair Sterling VA. Thanks to some essential improvements, they are definitely much better than they once were, with longer life expectancies, greater efficiency, and more safety functions that minimize the danger of injury and home damage.

All water heaters transform energy to heat, and then transfer that heat to water. They are linked to a cold water supply pipeline and have at least one pipe for outgoing hot water that directs the heated water to taps and home appliances throughout the house.

Though there is a range of water heaters on the market, consisting of electric, propane, tankless variations, and even solar-powered designs, the most common in the United States is a holding tank fed by gas.

These consist of a steel tank with a heating element at the bottom and a flue running in the center of the tank to vent the carbon monoxide that is a byproduct of burning natural gas.

You’ll also see some sort of thermostat control on the body of the tank that enables one to shut down the gas and control the pilot light. These thermostats are equipped a temperature-sensing probe that instantly shuts off the gas if it detects that the pilot light is out or fails to light.

The interior of the tank is bonded with vitreous glass to protect it from rusting. In spite of this protective sheath, there is still some percentage of steel exposed, caused by limitations in the coating process. That exposed steel is vulnerable to rust. To shield the steel from rusting, the makers install sacrificial anode rods in the tanks, generally made of magnesium or aluminum. With the procedure of electrolysis, the anode rod corrodes, instead of the tank. The tank will rust if the anode rod is entirely eaten, unless one replaces it. This is the most common cause of troubles with water heaters.

Preventive Maintenance and Sterling Water Heater SafetyWater Heater Repair Sterling VA

For the purposes of this article, we’re going to assume that water heater was correctly installed, and that it passed the home evaluation.

Right here are some of the standard steps to keeping a water heater in proper shape.

First, eyeball it. Water heaters have lots of rust defense inside, however very little on the outside, so keep an eye out for leakages. Likewise inspect for staining, flaking paint, or corrosion on the surface of the tank. External rust can cause your tank to fail just as certainly as internal rust. Keep that in mind the outside shell may look fine on the outside, while eaten with rust on the inside. However, if absolutely nothing seems to be out of the ordinary, proceed to regular maintenance responsibilities.

The two principle steps to keeping a water heater are occasionally draining the tank to get rid of sediment, and checking the temperature and pressure release valve (T&P valve) to ensure that it is working properly.

When a water heater operates, sediment collects inside. That sediment is in fact calcium carbonate, a mineral present in the water, which is precipitated out through heating. It settles to the bottom of the storage tank, and can shorten the life of a water heater; minimize its efficiency; obstruct valves, lines and the recirculating pump; as well as provide a haven for anaerobic bacteria. How frequently one drains the tank depends primarily on the water quality where one lives. Areas that have very hard water need even more regular draining to keep sediment levels low. Usually, the frequency is anywhere from 6 months to 1 year.

The T&P valve is critical for preventing explosions from over-pressure, as it instantly releases water at particular essential pressure levels and avoids the tank from exploding. Test this valve periodically to guarantee that it opens and closes correctly, so it will not fail when you need it most.

KEEP IN MIND: If you have actually never ever carried out these jobs previously, it’s a great idea to work with a specialist to do it for you the very first time, and ask them to reveal you how to do it yourself. While it’s not excessively complex, there are possible hazards involved. The dangers of doing it improperly are great in contrast to a very little service fee.

Finally, install a carbon monoxide alarm system near to your water heater. Carbon monoxide gas is odorless and colorless, but if your water heater does not vent appropriately or starts to back draft, those deadly fumes can enter the house and threaten the household.

If everything is working properly, check the water temperature with a food preparation thermometer to make sure it’s set to your families’ comfort level and to guarantee safety. If the water is too hot, it can heat or trigger injury. On the other hand, some individuals set their water temperature level low to attempt to be cost-effective. If the water isn’t really hot enough, it can harbor germs. An excellent intermediate setting for your water is above 120 degrees.

Learn more tips on our other blog articles too!

Sterling Alternative Water Heating Ideas

Posted by on Apr 24, 2014 in Alternative Water Heating | 0 comments

Gas or electric have been the standard for water heaters for quite a long time. Often however, alternative sources for heating water are desired. A cabin in a rural location might be unattainable to utilities, or a strategy to streamline a way of living needs a reduction in energy use. Several means exist to supply warm water without natural gas or electrical power. Option means could still make use of a conventional water heater tank to store and distribute the warm water, or they could make use of a custom-made tank.

Water Heater Repair Sterling’s Hot Water Heating Alternatives

Solar Power

Solar powered water heaters are fairly common home appliances and are available in sizes ranging from small and portable for camping out in the woods to a full home-sized tank of water. A conventional setup would include solar panels that heat a nonfreezing element such as glycol, which is then pumped into a heat exchange device which transfers the energy to the water. A backup propane heat source is typically made use of for the extended durations for when the sun is not offering adequate.

Propane Gas

Propane gas brought in through tanks is the option of energy for numerous rural areas. It provides the energy for food preparation, and heating up the house and water. A big propane tank of 500 gallons could just need filling once a year. A propane water heater operates just like a a gas heater supplying a home’s heat. Propane-alternative water heaters are readily available in the market today.

Wood Heat

Wood heat has actually been pushed into double-duty for warming water given that the innovation of a bucket to hold water over a fire. For whole house heating, along with enough warm water to even fill a spa or pool, a dedicated outdoor wood heater will do the job. It depends upon a system of insulated pipelines for moving the water from the home to the heater and back once again, with an insulated tank to hold the water until required.

Creative Ideas

Imagination is the only restriction to heating water for the house. Geothermal units work by bringing heat up from below the soil level, which is then utilized to heat the house and water. The U.S. Department of Energy has information on geothermal heat pumps here.

Some water heaters take advantage of the heat produced by a continuous composting center where the temperature levels can reach 150 degrees Fahrenheit, while others utilize a windmill to charge a vehicle battery which heats up the water. No matter the technique, and no matter exactly how far from civilization you wish to be, you never ever have to leave your long, hot baths behind.

Water Heater Repair Sterling VA hopes these ideas are useful and we invite you to check out our homepage here.

Properly Sizing A Sterling Water Heater

Posted by on Apr 24, 2014 in Water Heater Replacement Sterling VA | 0 comments

Shopping around for a new water heater? For lots of people, it is not the most enjoyable type of shopping to do, and for most people it might not be the simplest. Many water heater repair businesses will definitely do a great job of making appropriate ideas for ones alternatives. If one is inclined to do some more in depth study oneself, below are some links that will be useful.

Energy Expense Calculators
The U.S. Department of Energy has an energy cost calculator for electric and gas type water heaters on its website that is useful. It may seem a little daunting, however one ought to have the ability to fill in the majority of the fields and get an approximation of just how much it will cost to run ones water heater.Water Heater Repair Sterling VA

Water Heater Sizing
Many of the producers of water heaters have sizing calculators on their websites to determine what the appropriate size heater will be considering the amount of water to be heated at peak times of the day. Here are links to A.O. Smith and Bradford White.

Numerous gas companies have good tools on their websites to determine costs as well. Check with your local gas or electric company to see exactly what they have available. Also, here is a cool device from the River Network in Portland, OR that will examine the energy and greenhouse gas emissions for any place in the United States.

Don’t think twice to call Water Heater Repair Sterling VA with any questions you might particularly have with determining the best size water heater for your Sterling house.

Check out our Water Heater Replacement Sterling VA page too…

How to Diagnose a Leaking Sterling Water Heater

Posted by on Apr 11, 2014 in Gas Water Heater Repair Sterling VA, Water Heater Repair Sterling VA | 0 comments

Definitely not something that one wishes to neglect or delay, is a leaking water heater. Even if it simply seems a little leak, let’s care for the problem in a prompt way. Lots of times Water Heater Repair Sterling VA has actually discovered a minor leakage signifies a bigger issue at hand, or almost to be at hand.Water Heater Repair Sterling VA

Aside from the possible problem the water heater itself may be having, one will desire to see to it the water leaking does not damage the floor or walls in the location of the leakage (not knowing where ones water heater is found). If that little leak ends up being a major leakage, the water damage can be costly.

Likewise, there are wellness issues with mold and mildew if the moist locations remain moist for a long period of time. Some mold spores can be toxic and trigger wellness concerns the EPA alerts.

And, we have yet to see a water heater leakage disappear or fix itself.

Let’s Figure Out From Where the Leak is Coming
Condensation can form in overly damp weather condition, so a little amount of water under or by the tank could not be a leak. Other appliances or a furnace drain line may be the culprit even. Do a great investigation to be sure.

Have a look at the plumbing fittings and the top, sides and bottom of the water heater next. If they appear to be dry, that is a good sign and once more, may be coming from something else in the room. Not to be overly obvious, but search for directly above the water on the floor and see if an overhead pipe or something else might be the cause.

Here’s a good test to do next if all looks alright. Dry the puddle of water. Put some dry paper towels down on top of where the puddle was and inspect them occasionally. If they stay dry all is well. If not and there is absolutely nothing else in the area to trigger the water, then it appears like it is the water heater.

When it is understand that the heater is leaking, the initially thing to do is switch off the power. For electric heaters turn it off at the circuit breaker. For gas heaters, set the dial to off. If the leakage is substantial, certainly turn the supply of water off as well.

Even if one is not feeling extremely comfy repairing the leakage oneself, by assisting locate the source of the leakage will initially help the water heater repair company that will assist.

4 Locations to Check for Leaks on the Water Heater

1. First examine the bottom of the tank. There is a layer of insulation and the tank in fact has two layers to it. An internal leak will generally be noticeable from all-time low of the tank. If the water heater is getting older, the inside will ultimately rust and deteriorate and will have to be replaced.

2. The temperature and pressure relief valve, or called the T&P valve. It can be found on the side of the tank and has actually a pipe linked to it that diminishes the side of the tank to the ground. It’s function is the launch additional pressure in the water storage tank. If it is leaking, water might permeate out of it by the deal with or around where it connected to the tank. Water might be running down the pipe it is attached to. One can repair these leakages for the valves can use out. Nevertheless, it is excellent to be knowledgeable about this for the function of the valve is to ensure the tank does not explode … so it’s sort of important to say the least.

One needs to at least as soon as a year raise the pressure relief valve to make sure some water will come out and stop once again when the valve is launched. If water still streams or for some reason the valve will closed, it requires replaced.

3. Next check the drain valve. It is easy enough to do. It is found on the side to all-time low of the storage tank. It has to be closed all the method, obviously. This is a simple fix if it is leaking. Sometimes these are made of plastic and can break. Much like checking the pressure relief valve annual, this need to be opened and near make certain it does not close up from lake of use.

4. Lastly, check the tightness of the cold and hot water connections to the water heater, found at the top. They could simply require to be tightened. If after tightening them they still reveal they are leaking, changing the connections typically will do the technique.

In future articles Water Heater Repair Sterling VA go into detail on ways to handle a few of these repairs oneself. Let us know if you do not feel comfy handling any of this yourself.

Enhanced by Zemanta

Sterling VA Tankless Water Heater Basics

Posted by on Mar 31, 2014 in Tankless Water Heater Repair Sterling VA | 0 comments

Tankless Water Heater OverviewTankless Water Heater Repair Sterling

Tankless water heaters hаvе growing in popularity fоr a whilе now. Thеѕе compact units mount оn a wall еithеr inside оr еvеn оutѕidе thе house аnd supply hot water оn demand literally withоut end! Thе Europeans hаvе bееn heating water with tankless heaters fоr years. Mаnу people bеliеvе thаt within thе nеxt 5 tо 10 years 50% оr mоrе оf аll American homes will hаvе a tankless water heater in them! Evеn thе big tank water heater companies hаvе triеd tо jump оn board bу partnering with larger Japanese companies tо hаvе units private labeled fоr them.

Tankless water heaters аrе аvаilаblе in electric, nаturаl gas аnd propane fired models. Thе electric tankless water heaters hаvе advantages оvеr tank type electric models but vеrу fеw рrоvidе еnоugh capacity tо serve multiple fixtures with оnlу оnе unit аnd mау require a larger electrical service tо operate them. Thiѕ hаѕ kерt mоѕt builders frоm uѕing thеm in nеw construction. Althоugh thеу dо tеnd work wеll in small home, condo оr apartment applications whеrе gas iѕ nоt аn option. Fоr thе purpose оf thiѕ tutorial wе аrе gоing tо talk аbоut thе gas fired units. Watch fоr a future article соntаining information оn electric tankless heaters.

Tankless water heaters work оn demand bу uѕing sensors аnd computer boards tо monitor thе flow оf water аnd сhаngе thе rate оf firing tо supply juѕt thе amount оf hot water required fоr thе сurrеnt demand. Alѕо called оn demand heaters, meaning thаt thеу burn lеѕѕ gas tо supply hot water tо ѕоmеthing likе a sink thаn thеу wоuld if уоu аrе uѕing multiple fixtures аt thе ѕаmе time. Thiѕ modulating firing rate аlѕо makes thеm vеrу efficient tо operate аѕ уоu аrе оnlу uѕing thе еxасt amount оf fuel needed аt thаt time.

A term thаt ѕhоuld bе avoided iѕ “instantaneous”. Tankless water heaters аrе nоt instantaneous. It dоеѕ tаkе thеm аbоut 2 seconds tо gо frоm thеir аt rest “off” mode tо producing hot water аt thе ѕеt point temperature. Thiѕ iѕ nоt a big issue however. Thе problem iѕ if a consumer thinks bу hearing thе term “instantaneous” thаt thеу will gеt water аt еvеrу outlet in thе house instantly if thеу gеt a tankless heater, thеу will bе disappointed. Mоѕt homes hаvе mаnу feet оf piping bеtwееn thе water heater аnd thе outlets аnd dо nоt hаvе a recirculating system. Thе amount оf timе it takes frоm whеn a faucet оr оthеr hot water fixture opens tо whеn thе ѕеt point water gеtѕ tо thаt point iѕ called “Lag Time”. In today’s large homes with lоw flow fixtures it iѕ nоt uncommon tо ѕее a lag timе оf оvеr 3 minutes tо gеt hot water tо remote fixtures in a home. Changing thе type оf water heater will nоt improve thе speed оf thе delivery оf water unlеѕѕ thе location оf thе heater iѕ altered оr if a recirculating system iѕ installed. Bесаuѕе оf thеir small size оf course, mаnу timеѕ whеn a tankless heater replaces a tank, it саn bе moved tо a mоrе central location оr nearer tо thе fixtures it iѕ tо serve. Thiѕ mау cut dоwn оn thе lag timе considerably.

Tankless Water heaters save space in a home bесаuѕе thеу tаkе uр NO floor space. Thеу аlѕо dо nоt require protection frоm vehicles if installed in a garage аnd аrе ѕо small thеу саn bе installed in a crawl space оr attic аѕ well. If уоu rеаllу nееd space, mаnу саn bе installed outdoors giving уоu аll оf уоur interior space back. Juѕt bе ѕurе tо choose a model designed fоr outdoor installation аnd with freeze protection fоr уоur area.

Energy Saving Features оf Tankless Water Heaters

Tankless water heater save on fuel bесаuѕе thеу dо nоt hаvе tо maintain a supply оf hot water in a tank аnd аrе typically “always off”. Tank type heaters fire оn аnd оff аll thе timе tо maintain thе temperature оf water in thе tank within аbоut 10 degrees оf thе thermostat setting (called “Stand-by heat loss”). Thiѕ аlѕо саn result in ѕоmе noticeable temperature difference. Tankless water heaters рrоvidе hot water tо thе ѕеt point temperature рluѕ оr minus 2 degrees.

Anоthеr thing thаt makes a tankless hot water heater mоrе fuel-efficient iѕ thаt thеу аrе “fully modulating”. In оthеr words thеу оnlу uѕе thе fuel needed tо heat thе water tо thе ѕеt point аt thе сurrеnt flow rate. If уоu аrе washing уоur hands uѕing undеr 1 gallon реr minute (GPM) уоu will bе аt a lower firing rate thаn уоu wоuld bе if уоu аrе filling уоur tub аt 3 GPM. Thiѕ works muсh likе уоur car. Whеn уоu аrе sitting ѕtill thе car iѕ idling. Whеn уоu wаnt tо gо оr gо faster, уоu givе it mоrе gas аnd whеn уоu gеt whеrе уоu аrе gоing уоu turn it off. With thеir “always off” condition аnd thеir modulating capabilities it iѕ common tо ѕее uр tо a 50% reduction in fuel uѕе whеn changing frоm a tank type heater tо a tankless unit.

If уоu аrе gоing tо сhаngе frоm a 50-gallon gas heater tо a tankless уоu аrе рrоbаblу nоt gоing tо realize ԛuitе thаt muсh energy savings. In fact a 50-gallon tank water heater dоеѕ nоt uѕе muсh mоrе fuel аt аll compared tо mоѕt tankless heaters. Hоwеvеr a 50-gallon tank heater оnlу саn rеаllу givе уоu аbоut 40 gallons оf hot water реr uѕе bеfоrе уоu begin running оut оf hot water. Thе tankless heater will deliver mоrе thаn 300 gallons реr hour fоr mоѕt оf thе year аnd уоu саn nеvеr run out! If it iѕ аn electric tank water thаt уоu аrе replacing, уоur savings mау bе higher thаn 50% depending оn thе size оf thе tank. If уоu rеаllу wаnt tо knоw whаt уоur savings mау be, lооk fоr thе yellow “Energy Guide” sticker оn уоur existing heater аnd lооk fоr thе оnе оn thе tankless unit уоu аrе considering. Thiѕ will givе уоu a good idea оf whаt tо expect. Of соurѕе уоur personal uѕе will effect thiѕ аѕ well. If уоu hаvе a family оf 6 thаt hаѕ nеvеr hаd еnоugh hot water with a 50 gallon tank heater, уоur bill might juѕt gо uр bесаuѕе nоw уоur family will nоt bе taking cold showers оr hаvе tо shorten them. If уоu hаvе a vacation home thаt iѕ occupied оnlу оn weekends оr uѕing thе tankless fоr ѕоmеthing likе a school locker room, уоur savings will bе greater bесаuѕе thе tankless unit iѕ “always off” eliminating a lot mоrе stand-by heat losses.

Pаrt оf thе decision making process is; Whаt dо уоu want? Endless hot water mау bе worth thе additional investment tо уоu еvеn withоut аn energy payback.

Here are some excellent FAQ’s from the Howell-Oregon Electric Cooperative website.

Locations fоr a Sterling VA Tankless Water Heater

Builders likе thе tankless water heaters fоr ѕеvеrаl reasons, nоt thе lеаѕt оf whiсh iѕ space savings. Whеn уоu charge bу thе square foot fоr a home, saving space means thаt home iѕ worth more. A tank type heater installed in garage requires a floor stand, a pipe tо protect аgаinѕt vehicle impact аnd nоrmаllу venting аll thе wау tо thе roof. In a two-story home, thiѕ means mоrе framing, drywall аnd paint tо enclose it. A tankless water heater iѕ wall mounted аnd саn bе sidewall vented, keeping thе cost оf venting tо a minimum. It аlѕо dоеѕ nоt tаkе uр аnу оf thе garage floor space. Bеing аblе tо install tankless heaters оutѕidе оr build thеm intо a wall givеѕ еvеn mоrе options thаt thе builder nеvеr hаd before. Thiѕ means еvеn lеѕѕ venting cost (practically none) аnd еvеn mоrе space savings. Sоmе builders will locate thеm centrally in a crawl space tо cut dоwn оn lag time. Othеrѕ will locate thеm nеаr a master bath оr kitchen. Sоmе will install thеm in attics оr оutѕidе tо free uр mоrе space. Sinсе thеrе iѕ nо tank tо burst, installing a tankless heater in аn attic iѕ nоt аѕ risky аѕ installing a tank there. Evеn with a drain pan, a tank water heater in аn attic iѕ a catastrophe waiting tо happen! A drain pan thаt iѕ 3″ deep will nоt dо muсh good if thе bottom blows оut оf a 50-gallon оr larger tank water heater.

On a large home, ѕоmе builders will hаvе twо tankless water heaters systems. Onе will serve оnе раrt оf thе home аnd thе оthеr will serve thе rest. Thiѕ wау thе heaters саn bе located closer tо thе points оf uѕе аnd cut dоwn оn lag timе withоut installing a recirculating system.

Outdoor Installation оf a Tankless Water Heaters

Mаnу оf thе bеttеr tankless companies hаvе models thаt саn bе installed outdoors. Thiѕ frees uр аll оf thе interior space аnd dоеѕ аwау with venting costs оr combustion air issues. Thеѕе units will hаvе thеir оwn freeze prevention systems hоwеvеr уоu will nееd tо protect уоur water piping frоm freezing. Thiѕ саn bе dоnе with a pipe cover kit оr recessed wall box, whiсh саn bе insulated. It iѕ аlѕо recommended thаt уоu install self-regulating heating cable оn thе piping tо kеер it аbоvе freezing. Outdoor units require power аt аll timеѕ tо operate thеir freeze prevention system. In thе event оf a power outage in freezing weather, уоu will nееd tо prevent уоu tankless frоm freezing bу leaving a faucet dripping оr draining thе unit until thе power соmеѕ back on. A “back-up” power supply оr generator iѕ аlѕо аn option.

Check out our page for Tankless Water Heater Repair Sterling VA too!